LECTROSONICS DSQD/DANTE
Lectrosonics DSQD digital 4-channel ½-rack receiver with Dante, 470-614 MHz
€ 5,521.00 Excl. VAT
Available on backorder
The DSQD half rack receiver with analog and digital Dante network audio outputs utilizes the Lectrosonics signature digital architecture with remarkable audio quality and ultra-low latency. The receiver includes an extended operating range rivaling the best analog and Digital Hybrid Wireless systems with continuously tunable tracking filters covering 470 to 614 MHz.
The DSQD receiver is a four-channel design with a host mainframe that contains the DSP, microprocessor, antenna multicoupler and control interface. Antenna ports on the rear panel accept input from remote antennas, with a loop-thru output to another mainframe using the internal multicoupler. A kit is also available to mount antenna inputs (BNC connectors) on the front panel.
FEATURES:
- four-channel, half-rack design
- continuously tunable tracking filters covering 470.100-614.375 MHz
- compatible with D Squared, DSW, Duet and Digital Hybrid Wireless transmitters
- built-in wideband antenna multicoupler with loop-thru for additional receivers
- antenna bias power enabled from the front panel
- IR bi-directional port for transmitter setup
- analog and Dante audio outputs with TalkBack (in applicable RX modes)
- Ethernet and USB interface
| Category | Specification | Detail |
| RF & Wireless | Operating Spectrum | 470.100 to 614.375 MHz |
| RF & Wireless | Frequency Adjustment Steps | 25 kHz |
| RF & Wireless | Digital Modulation | 8PSK with forward error correction |
| RF & Wireless | Adjacent Channel Isolation | >85 dB |
| RF & Wireless | Diversity Technique | Noiseless antenna switching |
| RF & Wireless | Sensitivity | -98 dBm |
| RF & Wireless | Antenna Inputs/Outputs | Dual BNC female, 50 ohm impedance |
| Security / Digital | Encryption |
AES 256-CTR (per FIPS 197 and FIPS 140-2)
|
| Audio Performance | Sampling Size and Rate | 24-bit, 48 kHz |
| Audio Performance | Data Encoding | Proprietary ADPCM |
| Audio Performance | System Latency (Digital Output) |
D2 mode: 0.75 ms plus Dante | Duet mode: 1.4 ms plus Dante | Hybrid modes: 2.0 ms plus Dante
|
| Audio Performance | System Latency (Analog Output) |
D2 mode: 1.25 ms | Duet mode: 1.9 ms | Hybrid modes: 2.5 ms
|
| Audio Performance | Frequency Response | 20 Hz – 20 KHz, +/-1 dB |
| Audio Performance | THD+N | 0.05% (1 KHz @-10 dBFS) |
| Audio Performance | Dynamic Range | 108 dB A-wtd, NR=NORMAL |
| Audio Outputs | Analog Audio Outputs (XLR) | Balanced, -35 to +8 dBu |
| Audio Outputs | Headphone Output | 3.5mm phone jack |
| Connectivity / Interfaces | Dante Output |
RJ45 Gigabit Ethernet (Dante model only)
|
| Connectivity / Interfaces | AES3 Output | TA3M (AES3 model only) |
| Power | External DC Power | 7 to 18 VDC, 2.5A (max) |
| Physical | Dimensions (W x H x D) | 213 x 44.5 x 187 mm |
| Physical | Weight | 880 grams |
| Included Accessories | 1x USB cable, 1x rear tie bracket, 1x front tie bracket, 1x rack flange bracket, 1x rack “D” handle, 1x SCR10 cap screw, 1x spacer, 1x rubber feet (large, stick on), 1x hex key, 1x hole plug, 2x right angle BNC antenna (block 20), 2x right angle BNC antenna (block 22), 1x AC power supply | |
You may also like…
LECTROSONICS
Lectrosonics plug-on transmitter with phantom power, dual AA battery, wideband
This product has multiple variants. The options may be chosen on the product page
LECTROSONICS
Lectrosonics DSSM water-resistant micro belt pack transmitter, Lemo 3p input, incl. rechargeable Li-Ion battery and dual USB charger, block A1-B1 470-614 MHz
This product has multiple variants. The options may be chosen on the product page
LECTROSONICS
Lectrosonics DSR4 four channel digital slot-mount receiver, rear panel adapter not included
This product has multiple variants. The options may be chosen on the product page
LECTROSONICS
Lectrosonics DBu digital belt pack transmitter with Lemo 3p connector, dual AA battery, 470-614 MHz
This product has multiple variants. The options may be chosen on the product page
