LECTROSONICS HMA/E01 PLUG-ON TRANSMITTER
Lectrosonics plug-on transmitter with phantom power, dual AA battery, wideband
€ 1,455.00 Excl. VAT
FEATURES
- Accepts microphone or line level signals
- Selectable 5, 15, 48 volt phantom power
- 76 MHz tuning range in 100 kHz or 25 kHz steps for up to 3072 frequencies
- Selectable 25/50 mW output power
- Adjustable low frequency roll-off
- Powered by two AA batteries
- USB port for firmware updates
- IR (infrared) port for fast setup
- Solid machined aluminium housing
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
The design includes a wide tuning range of up to 76 MHz, with tuning steps in increments of 100 kHz or 25 kHz for up to 3072 frequencies. The tuning range covers three standard 25.6 MHz Lectrosonics frequency blocks. Each of the standard blocks includes 256 different pilot tone frequencies for compatibility with all Digital Hybrid Wireless receivers.
DSP compatibility modes are also included to work with legacy Lectrosonics analog wireless microphone receivers and IFB receivers, as well as some receivers from other manufacturers.
INCLUDED ACCESSORIES
2 – AA Alkaline Batteries
1 – HM Pouch (Part #PHTRAN3)
1 – Quickstart Guide
| Frequency Selection Steps | Selectable; 100 kHz or 25 kHz |
|---|---|
| RF Power output | HMa: Selectable 100 or 50 mW HMa/E01: Selectable 25 or 50 mW HMa/E02: 10 mW HMa/E06: Selectable 50 or 100 mW EIRP HMa/E07-941: Selectable 50 or 100 mW HMa-941: Selectable 50 or 100 mW |
| Compatibility Modes | HMa: Nu Hybrid, Mode 3, IFB HMa/E01: Digital Hybrid, Mode 3, IFB HMa/E02: Digital Hybrid, Mode 3, IFB HMa/E06: Digital Hybrid,Mode 3, IFB HMa/E07-941, HMa-941: Digital Hybrid, 200 Series, 100 Series, Mode 3, Mode 6, Mode 7, IFB |
| Pilot tone | 25 to 32 kHz; 5 kHz deviation (in the Digital Hybrid mode) |
| Frequency stability | ± 0.002% |
| Spurious radiation: | HMa/E01/E02/941/X: 60 dB below carrier HMa: Compliant with ETSI EN 300 422-1 v1.4.2 |
| Equivalent input noise | –125 dBV (A-weighted) |
| Input level | Nominal 2 mV to 300 mV, before limiting. Greater than 1V maximum, with limiting. |
| Input impedance | 1K Ohm |
| Input limiter | Dual envelope “soft” limiter; greater than 30 dB range |
| Gain control range | 55 dB; panel mounted membrane switches |
| Operating temp. range | Celsius: -20° – 40° (Farenheit: -5° – 104°) |
| Modulation indicators | Dual bi-colour LEDs indicate modulation of -20, -10, 0, +10 dB referenced to full modulation |
| Frequency Response | 35 Hz to 20 kHz (+/-1dB); |
| Low frequency Roll-off | Adjustable for -3dB @30, 50, 70, 100, (120 or 150 Hz) |
| THD | 0.2% (typ. 100 Hz to 20 kHz – see table) |
| Input Dynamic Range | 125 dB (with full Tx limiting) |
| Controls & Indicators | Power/Phantom “ON-OFF” Phantom voltage selector Audio input gain LCD w/membrane switches LED audio level indicators |
| Audio Input Jack | Standard 3-pin XLR (female) |
| Phantom Power | 5V @ 18 mA max., 15V @ 15 mA max. and 48 V @ 4 mA max., plus “OFF” |
| USB port | Used for firmware updates |
| IR (infrared) port | For quick setup by transferring settings from an IR enabled receiver |
| Antenna | Housing and attached microphone form the antenna |
| Battery | Two 1.5 Volt AA alkaline |
| Battery Life (Duracell Ultra) | AA alkaline; No Phantom Power: 5h 0m* AA alkaline; 48V Phantom Power: 3h 30m** * Tested with a dynamic microphone ** Tested with a Sanken CS1 for a phantom-powered microphone |
| Weight | 6.7 oz (190 grams) without batteries |
| Dimensions | 107.95×41.15×35.05 mm (4.25×1.62×1.38 inches) |
| Emission Designator | A1: 44K3F3E B2: 57K9F3E HMa/E06: 180KF3E HMa/E07-941: 110KF3E |
| Frequency | A1 (470.100-537.575 MHz), B1 (537.600-614.375 MHz), C1 (614.400-691.175 MHz) |
|---|
