LECTROSONICS Duet M2T-DANTE/E01
RACK IEM/IFB TRANSMITTER, DIGITAL DUAL STEREO, DANTE INPUTS
€ 2,810.00 Excl. VAT
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a half-rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
- IEM (Wireless Monitor) with digital RF transmission
- 2 independent stereo audio transmissions per 1/2 RV enclosure
- USB port for firmware updates
- Fully Dante™ compatible
- AES 256 bit encryption with v3.X firmware
- Up to 50 mW per Rf carrier
- All metal housing
- Compatible with Wireless Designer™ Software
- Cable USB
- Bracket Rear Tie M2T/M4T
- Bracket Front Tie M2T/M4T
- Rack Flange Bracket
- Rack Handle RMP2T
- 4 Cap Screw
- 4 Rubber Foot (Large)
- Hex L Key Wrench
- Hole Plug
- 2 Antenna
- DCR15/4AU DC Power Supply
- Instruction Manual
| Category | Specification | Detail |
| RF & Wireless | System Type |
IEM (Wireless Monitor) with digital RF transmission
|
| RF & Wireless | Operating Frequencies | 470-614 MHz or 537-691 MHz |
| RF & Wireless | RF Power Output |
Adjustable on each carrier to 10, 25 or 50 mW
|
| RF & Wireless | Antenna Output | 2x BNC sockets |
| Audio Performance | Audio Resolution | 24-bit digital audio |
| Audio Inputs | Input Connectors | 4 x line level combo XLR/TRS |
| Audio Outputs | Transmission Channels |
2 independent stereo audio transmissions per 1/2 RU enclosure
|
| Audio Outputs | Headphone Monitor | 3.5 mm stereo headphone jack |
| Connectivity / Interfaces | Dante | Fully Dante compatible |
| Connectivity / Interfaces | USB Port | For firmware updates |
| Interfaces & Controls | IR Port | Infrared port for fast setup |
| Interfaces & Controls | Software Compatibility |
Compatible with Lectrosonics’ Wireless Designer software
|
| Power | Power Requirements | 9-18 VDC |
| Physical | Housing | Solid machined aluminum housing |
| Physical | Dimensions (H x W x D) | 44.45 x 212.7 x 196.8 mm |
| Frequency Band | Block A1B1 – 470.100 to 614.375 MHz (ch 21 to 39), Block B1C1 – 537.600 to 691.175 MHz (ch 29 to 48) |
|---|
You may also like…
LECTROSONICS
€ 3,720.00 Excl. VAT
Lectrosonics Duet M2C-L active 8:1 antenna combiner, block A1-C1 470-692 MHz
LECTROSONICS
€ 1,860.00 Excl. VAT
Lectrosonics DCHT digital camera hop transmitter, Duet compatible, dual AA battery, block A1-B1 470-614 MHz
This product has multiple variants. The options may be chosen on the product page
€ 1,400.00 Excl. VAT
Lectrosonics Duet M2Ra digital stereo IEM bodypack receiver, dual AA battery, block A1-B1 470-614 MHz
This product has multiple variants. The options may be chosen on the product page
